Homeowner guide
The garage door that wants to go up
A tired spring gets all the attention, and a door that feels light seems like a lucky one. A door that rises when you let go, or settles light on the slab, has a spring too strong for it, and that is as much a fitting fault as a weak one.
Why does my garage door rise on its own when I let go of it?
A balanced garage door stays wherever it stops. One that drifts upward from waist height, won’t settle onto the slab, or jumps up the last few feet as it opens is carrying more spring than door. The springs were meant to cancel the door’s weight and they are overpowering it instead, and that calls for garage door spring repair as surely as a weak spring does.
A spring losing its strength shows the opposite way. That door sinks and needs help going up. The over-sprung one feels easy, which is why it gets lived with for years.
Where it tends to show up:
- The 30-second balance test in the tune-up guide ends with the door creeping up instead of holding still
- Pulled closed by hand, it resists the whole way down and starts back up as soon as you let go
- With the door closed, the bottom edge rests on the slab without pressing down, so daylight shows under part of the seal
How does a garage door end up with too much spring?
Almost always at the last time the springs were touched. There are three usual routes, and they can stack on the same door.
The first is a spring picked from what was on the truck. A proper garage door spring replacement starts by measuring the old spring and the door, so the new one is sized to the weight it has to carry. Fitted from the nearest size on hand, a spring a step too heavy lifts more than the door weighs, and nothing about it looks wrong from the floor.
The second is winding added to make a spring feel right. A pair that is undersized for the door, or tired, can be given more tension so the door lifts easily again. On the day it is done the door goes up like new. Spread across the full travel, that extra tension leaves the door eager at one end and the spring working harder than it was made to for every cycle it has left.
The third is a door that got lighter while its springs stayed. A heavy wood door traded for a single-layer steel one, or a few wood sections swapped for steel, takes real weight off the shaft. A new install should get new springs sized to the new door, which is how ours are done, but on a garage that has seen a door or two come and go since it was framed, the spring above the opening is not always the one that came with the door below it.
What does an over-sprung door do to the opener?
It turns the opener into the thing holding the door down. A balanced door asks the opener to steer it both ways. An over-sprung one goes up almost by itself, so the up run feels fine, and then every close is the motor pulling the door down against the spring and keeping it pinned there.
The signs usually get blamed on the opener.
The door comes down and reverses a few inches from the floor with nothing in the way. The opener reads the extra effort near the bottom as an obstruction and does what it is supposed to do. A door that closes and then lifts a little once the motor stops is the same problem, with the spring taking up the slack in the drive.
The usual reaction is to turn the close force up until the reversing stops. That quiets the symptom and takes away margin from the safety reverse, since the opener now has to feel a lot more resistance before it backs off a bumper or a bike. The drive gear and trolley take the load on every close, which wears them faster than a door that balances.
On a door like this, garage door opener repair starts at the springs. Force and travel settings get set after the door balances, never as a substitute for it, and a new opener on the same springs ends up in the same spot.
Why won’t an over-sprung door seal at the bottom?
A closed door seals with its own weight. The rubber along the bottom edge is supposed to crush against the slab and fill the dips in the concrete. When the spring is carrying more than the door, the door rests light, the rubber barely touches, and the gaps stay open. In Kay County that means the south wind pushing red dirt across the floor and, in an ice storm, meltwater running under the edge instead of off it. Swapping the seal doesn’t change that, since the new rubber sits on the slab as lightly as the old.
Why is backing a spring off not a homeowner adjustment?
An over-wound spring stores more energy than a correctly sized one, and that makes it the more dangerous of the two to work on. Taking tension off is the same winding work as putting it on, with the spring at its most loaded at the moment the work starts. Hands and bars are in the path if anything slips. That is the part of every spring job that hurts people, and it is covered in plain terms in what a wound torsion spring does when the work slips.
There’s a second reason it doesn’t work out. A spring that is the wrong size for the door can’t be wound into the right one. Backed off far enough to stop the door rising, it often leaves the door heavy at another point in the travel, so the fix is a spring matched to the door, set and then checked at more than one height.
What does correcting an over-sprung door cost?
That depends on the spring. If it is the right size and in good shape, and only the tension is off, re-balancing sits inside a service visit. The tune-up and safety inspection runs $80 - $150 here, and balance and force settings are on that visit’s list.
If the spring is wrong for the door, or has spent years running over-wound and is worn, the fix is a replacement, $220 - $400 for the pair on a two-car door. Both ranges are on the page for what re-balancing and new springs cost, and the written figure for your door comes before any spring is touched.