Homeowner guide
When the hand chain on a shop door gets harder to pull
Plenty of big doors around Kay County never had an opener. Somebody walks to the jamb and pulls a loop of chain, and whoever does that every morning knows the door better than anyone. Few of them know that the effort on the chain is a reading of the springs.
Out along the industrial edge by the rail line, in the shop buildings on acreages, and on the ag doors from Tonkawa to Newkirk that are wide enough for a combine header, a lot of overhead doors still go up by hand chain. The chain hangs in a loop beside the door, usually worn bright at the height where everyone grabs it.
Why is the chain on our overhead door getting harder to pull?
The chain does not lift the door. It turns a shaft or a barrel through the hoist’s gearing, and the springs carry the weight. When the pull creeps up month by month, one of three things has changed: the springs are giving up strength, the hoist’s reduction gearing or bearings have gone dry or worn, or the door is dragging in its tracks or guides. Sorting out which one is the first step of commercial garage door repair on a hoist door.
A balanced door with a healthy hoist takes a steady, moderate pull from the floor to the top. The gearing trades distance for force, which is why there are so many feet of chain for a few feet of door. Any extra effort on the chain is weight or friction the springs and the hoist are no longer handling, and the person on the chain makes up the difference.
The change is slow enough to miss. Nobody notices one more ounce a week. Somebody back from a few days off, or a new hand on the crew, often feels it first.
What does a chain hoist actually turn?
On a sectional door, the hoist turns the torsion shaft above the opening. The cable drums on each end of that shaft wind the lift cables, and the springs wound around the shaft do the lifting. On a rolling steel door, the hoist turns the barrel the curtain wraps around, and the spring sits inside that barrel.
So the same stiff chain points at a different spring on each kind of commercial overhead door. On a sectional it is out in the open on the shaft. On a rolling door it is hidden in the barrel, and the only sign from the floor is the chain.
How can you tell the springs from the hoist from the tracks by the chain alone?
By where the effort changes and what you hear while you pull. Effort that is heavy all the way points at the springs, effort that spikes at one spot points at the tracks or guides, and noise from the hoist box points at the hoist. The finer signs:
- Stiff the whole way up, about the same at the bottom as at the top. That is spring strength. The springs are carrying less of the door than they used to.
- Easy most of the way, then hard at one spot. Something along the travel is catching, usually a bent track, a dented slat or section, or a guide that has been bumped.
- Pause partway up and the door sinks, or creeps upward. The springs and the door are out of balance.
- Grinding, clicking or a rough, notchy feel coming from the hoist box itself. The reduction gearing or its bearings.
- The chain skips or jumps on its wheel. A worn chain wheel or a chain that has stretched.
- One side of the door rises ahead of the other. A cable or a drum on the low side.
A chain that locks up all at once, or a bang from the shaft or the barrel, means stop. The door stays at whatever height it reached, with nobody under it, and the spring is the technician’s job.
What happens if a stiff hoist door is left alone?
The spring keeps weakening, and everything downstream of it picks up the load. On a sectional, the cables and drums carry more of the door on every cycle and the hoist gearing takes more strain from every pull. On a rolling door, whatever the barrel spring stops carrying lands on the hoist. Sooner or later one of those parts lets go.
When that happens, the door is dead weight. A door with a broken spring or a snapped cable stays down. It does not get hauled up on the chain to get a truck out, and nobody should be standing under it trying. If a piece of equipment is shut inside, that is what the emergency garage door repair page is for.
For a shop, the bigger cost is usually the bay, out of service from the day the part lets go until the door is repaired.
Can an operator go on a door that runs on a hand chain?
Usually, yes. On most hoist doors the operator mounts beside the shaft or the barrel and drives it directly, as a jackshaft or hoist-type unit, and the hand chain stays on the door as the backup for when an ice storm takes the power out.
The door gets balanced first. An operator hung on a door with tired springs strains the same way the person on the chain did, and the motor and its gearing wear out early. Whatever made the chain stiff gets sorted so the door runs smooth by hand, and the motor goes on after that.
An operated commercial door also gets photo eyes and a sensing edge along the bottom, since nobody is standing at the jamb watching it close anymore. On a tall shop door, the operator usually ends up on the wall rather than the ceiling, and the overhead door on a metal shop building explains why a high-lift door takes a wall-mounted unit.
When is the hoist itself worn out?
A hoist that has been worked against a heavy, out-of-balance door for years wears its gears and its chain wheel the way any drive does. If the door has been balanced and the hoist still grinds, the chain still skips, or the wheel’s pockets are worn smooth, the hoist is due for replacement rather than another round of attention.
That gets quoted per door, in writing, the same as all commercial work, and how commercial work gets priced here covers what goes into the figure.